Polyolefin blends
Somayeh Rafiei; Davood Soudbar; Minoo Sadri; Fatemeh Shafiei
Abstract
Thermoplastic vulcanizates (TPVs) were prepared based on polypropylene (PP) and polybutadiene rubber (PBR) at different PP/PBR compositions (70/30 and 60/40). PP-grafted-maleic anhydride (PP-g-MA) was introduced into the TPVs at different concentrations (10 and 20%). The compatibilizing effect of PP-g-MA ...
Read More
Thermoplastic vulcanizates (TPVs) were prepared based on polypropylene (PP) and polybutadiene rubber (PBR) at different PP/PBR compositions (70/30 and 60/40). PP-grafted-maleic anhydride (PP-g-MA) was introduced into the TPVs at different concentrations (10 and 20%). The compatibilizing effect of PP-g-MA was demonstrated through cross-sectional morphology. PP-g-MA exhibited a suppressing impact on the coalescence of the rubber domains, leading to a finer and more uniform distribution of the PBR phase. Due to the higher rubber content, the compatibilizing effect was more pronounced for the 60/40 composition, which was on the averge of forming a co-continuous morphology. However, it was found that a higher PP-g-MA content is needed to effectively compatibilize the TPVs. Rheological results revealed opposing effects on the viscoelastic response of the system. However, the elastic response was intensified once higher content of PP-g-MA was used, suggesting its compatibilizing role. Dynamic mechanical analysis results proved the existence of opposing effects and revealed the profound compatibilizing effects of PP-g-MA, especially at higher content (20%). Izod impact strength exhibited moderate and notable enhancements in both TPV compositions by adding 10% and 20% of PP-g-MA, respectively, attributed to the highly increased compatibility of the PP/PBR TPVs, especially at higher levels of PP-g-MA content.
Olefin polymerization and copolymerization
Ahmad-Ali Shokri; Saeid Talebi; Mehdi Salami-Kalajahi
Abstract
Laboratory runs can be minimized via experimental design which yields the optimum and best data regarding the independent parameters. In this research work, response surface methodology (RSM) based on a threelevel central composite design (CCD) was utilized to optimize and evaluate the interactive effects ...
Read More
Laboratory runs can be minimized via experimental design which yields the optimum and best data regarding the independent parameters. In this research work, response surface methodology (RSM) based on a threelevel central composite design (CCD) was utilized to optimize and evaluate the interactive effects of processing conditions for polymerization of 1,3-butadiene (Bd) diene monomer using Ziegler-Natta catalyst. The polybutadiene rubber (PBR) having different cis content and molecular weight was obtained. The catalyst components included neodymium versatate (NdV3) as catalyst, triethyl aluminum (TEAL) as cocatalyst or activator, and ethylaluminum sesquichloride (EASC) as chloride donor. For the modeling, three independent variables, namely monomer concentration (8-28 wt%), reaction time (1.5-2.5 h), and reaction temperature (45-75ºC) at three levels were selected to optimize the dependent variables or responses including monomer conversion, viscosity-average molecular weight and the cis isomer content of the obtained polymer. The interaction between three crucial parameters was studied and modeled. Quadratic models were obtained to relate process conditions to dependent variables. It was observed that the optimal conditions predicted by RSM were consistent with the experimental data. Statistical analysis demonstrated that concentration of the monomer and the time of reaction significantly affected cis content. Moreover, processing conditions to achieve the desired response variables were predicted and experimentally approved. The optimal reaction conditions derived from RSM are monomer concentration = 19 wt%, polymerization time = 2 hours, and polymerization temperature = 50ºC. Polymerization was carried out at optimum conditions. The appropriate level of dependent variables including 94.2% monomer conversion, 151812 g/mol viscosity-average molecular weight and 98.8% cis content was acquired.