Polymer processing
Mohammadreza Rahnama; Abdulrasoul Oromiehie; Shervin Ahmadi; Ismaeil Ghasemi
Abstract
In this research, high oxygen-barrier films were organized based on low-density polyethylene (LDPE)/ ethylene vinyl alcohol (EVOH)/ polyethylene-grafted maleic anhydride (LDPE-g-MA) compatibilizer. The effects of 10–30 wt. % EVOH and 0–10 wt. % LDPE-g-MA loadings on the properties of final ...
Read More
In this research, high oxygen-barrier films were organized based on low-density polyethylene (LDPE)/ ethylene vinyl alcohol (EVOH)/ polyethylene-grafted maleic anhydride (LDPE-g-MA) compatibilizer. The effects of 10–30 wt. % EVOH and 0–10 wt. % LDPE-g-MA loadings on the properties of final films were evaluated. The morphology of specimens was observed by using scanning electron microscopy (SEM). Oxygen transfer rate (OTR) results revealed that the addition of EVOH up to 30 wt. % to neat LDPE could significantly decrease oxygen permeability. The LDPE-g-MA which increased the permeability needed to be fine-tuned its amount based on the EVOH loading in different samples. The experimental results revealed that the addition of 30 wt. % EVOH to the LDPE matrix without adding LDPE-g-MA gave the best oxygen barrier properties. Elastic modulus and tensile strength increased with incorporation of EVOH and LDPE-g-MA into the polyethylene matrix. On the other hand, elongation-at-break decreased with the addition of EVOH and increased with the introduction of compatibilizer to the samples. Incorporation of EVOH and LDPE-g-MA into the LDPE matrix and increasing their amounts led to higher storage modulus and zero shear rate viscosity, but lowered the frequency value at the intersection point of storage modulus (G') and loss modulus (G''). The only exception was that in the samples without compatibilizer, the increase in the EVOH content resulted in a lower zero shear rate viscosity and a higher frequency value at the intersection point of G' and G''.
Characterization
Sepideh Gomari; Ismaeil Ghasemi; Mohammad Karrabi; Hamed Azizi
Abstract
Nanocomposites based on polyamide 6 (PA6) and poly(ethylene-co-1-butene)-graft-maleic anhydride (EB-g- MAH) blends have been prepared via melt mixing. The effect of blend ratio and organoclay concentration on the crystallization and melting behavior of specimens were studied. Three types of commercial ...
Read More
Nanocomposites based on polyamide 6 (PA6) and poly(ethylene-co-1-butene)-graft-maleic anhydride (EB-g- MAH) blends have been prepared via melt mixing. The effect of blend ratio and organoclay concentration on the crystallization and melting behavior of specimens were studied. Three types of commercial organo-modified clay (Cloisite 30B, Cloisite 15A and Cloisite 20A) were employed to assess the importance of the nanoclay polarity and gallery distance. The crystallization behavior was investigated using differential scanning calorimetry (DSC) and wide angle X-ray diffraction spectroscopy (WAXD). The strong interactions between amine end groups of PA6 and maleic anhydride groups of EB-g-MAH led to complete inhibition of EB-g-MAH crystallization according to the DSC results. A transformation from the α form to the γ form crystals of PA6, induced by both organoclays and EB-g-MAH, was monitored by WAXD and DSC. Small angle X-ray scattering (SAXS) was used to evaluate the morphology of nanocomposites. Moreover, transmission electron microscopy (TEM) was conducted to determine the location of organoclays and indicated that the organoclays mainly present in the PA6 matrix and rarely distribute in the EB-g-MAH phase in the case of low polarity organoclays. It was also evidenced that the organoclay with the most affinity to PA6 (Cloisite 30B) had the largest effect on the thermal and crystallization behavior of this phase in the blend.
